Technical data sheets
Aluminium Alloy | BS-L
L59 H16 or H26 Sheet
Applications:
Equipment for heating and cooling: heat exchangers, air condition evaporators, motor vehicle radiators, aircraft and military components, freezer linings, office equipment. Tubing, piping. Cladding alloy. Pressure vessels.
Characteristic Properties:
Very good resistance to atmospheric corrosion. Very good weldability. Good formability by pressing, drawing and roll forming. Medium strength alloy. Better mechanical properties (in particular at elevated temperatures) than 1xxx-alloys. Properties very close to those of 3003.
Precautions and Warnings:
Actual performance requires careful design of tools, lubrication and metal surface condition.
Chemical Composition
|
BS 4L59(1985) Alloy L59 |
|
|---|---|
| Chemical Element | % Present |
| Aluminium (Al) | balance |
| Other (Each) | 0.05 max |
| Copper (Cu) | 0.1 max |
| Titanium + Zirconium (Ti+Zr) | 0.1 max |
| Chromium (Cr) | 0.1 max |
| Others (Total) | 0.15 max |
| Zinc (Zn) | 0.2 max |
| Magnesium (Mg) | 0.3 max |
| Silicon (Si) | 0.5 max |
| Iron (Fe) | 0.7 max |
| Manganese (Mn) | 0.9 - 1.5 |
The material shall be supplied cold rolled (H16) or cold rolled and partially annealed (H26).
Alloy Designations
Aluminium alloy L59 - 3103 is covered by Standard BS EN 4L59 (1985)
Temper Types
The most common tempers for L59 - 3103 aluminium are:
- H16
- H26
Supplied Forms
L59 - 3103 aluminium is supplied in the following forms:
- Sheet
- Strip
Generic Physical Properties
| Physical Property | Value |
|---|---|
| Density | 2.61 g/cm³ |
| Melting Point | 655 °C |
| Thermal Expansion | 23.1 x10^-6 /K |
| Modulus of Elasticity | 69.5 GPa |
| Thermal Conductivity | 160 W/m.K |
| Electrical Resistivity | 42 % IACS |
Mechanical Properties
|
BS 4L59(1985) Sheet - 0.4mm to 0.8mm |
|
|---|---|
| Mechanical Property | Value |
| Elongation A50 mm | 2 Min % |
| Tensile Strength | 160 Min - 195 Max N/mm2 |
Mechanical properties relate to material with a nominal thickness of 0.4mm up to and including 0.8mm. The specification contains other values for different material thicknesses.
Download PDF
Last updated Thursday, January 9, 2014
Disclaimer
This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.
Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.
The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.
Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.
Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.