Technical data sheets
Aluminium Alloy | BS-L
L113 T6 Sheet
Aluminium alloy L113 – 6082T6 is a medium strength alloy with excellent corrosion resistance. It has the highest strength of the 6000 series alloys. Alloy 6082 is known as a structural alloy. In plate form, 6082 is the alloy most commonly used for machining. As a relatively new alloy, the higher strength of 6082 has seen it replace 6061 in many applications. The addition of a large amount of manganese controls the grain structure which in turn results in a stronger alloy.
In T6 temper, the alloy machines well.
Chemical Composition
|
BS L113(1971) Alloy L113 |
|
|---|---|
| Chemical Element | % Present |
| Aluminium (Al) | balance |
| Lead (Pb) | 0.05 max |
| Tin (Sn) | 0.05 max |
| Copper (Cu) | 0.1 max |
| Nickel (Ni) | 0.1 max |
| Titanium (Ti) | 0.2 max |
| Zinc (Zn) | 0.2 max |
| Chromium (Cr) | 0.25 max |
| Iron (Fe) | 0.5 max |
| Manganese (Mn) | 0.4 - 1 |
| Magnesium (Mg) | 0.5 - 1.2 |
| Silicon (Si) | 0.7 - 1.3 |
Alloy Designations
Aluminium alloy L113 has similarities to the following standard designations and specifications but may not be a direct equivalent:
6082
Temper Types
The most common temper for L113 – 6082 aluminium is:
- T6
Supplied Forms
L113-6082T6 aluminium is supplied in sheet, strip and plate.
- Plate
- Sheet
- Strip
Generic Physical Properties
| Physical Property | Value |
|---|---|
| Density | 2.70 g/cm³ |
| Melting Point | 555 °C |
| Thermal Expansion | 24 x10^-6 /K |
| Modulus of Elasticity | 70 GPa |
| Thermal Conductivity | 180 W/m.K |
| Electrical Resistivity | 0.038 x10^-6 Ω .m |
Mechanical Properties
|
BS L113(1971) Sheet - 0.2mm to 3.0mm inc. |
|
|---|---|
| Mechanical Property | Value |
| Elongation A50 mm | 8 Min % |
| Tensile Strength | 295 Min N/mm2 |
| 0.2% Proof Stress | 255 Min N/mm2 |
Download PDF
Last updated Friday, July 8, 2016
Disclaimer
This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.
Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.
The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.
Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.
Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.